Sort by:
3 products
3 products
U075CTL010 Features:
- All in one construction for factory assured terminations
- Rolled edge door for cord protection
- Heavy 16 ga galvanized zinc coated steel with highest quality electro deposition finish resists corrosion and fading
- Welded flange, NEMA 3R construction for lasting service in outdoor installations
- All components are factory wired and assembled, reducing installation time
MIDWEST R075C010 100A SURFACE 50amp 30amp and 20amp GFCI Ringless - Metered
MIDWEST R075C010 100A SURFACE 50amp 30amp and 20amp GFCI Ringless - Metered
Constructed of G90 galvanized steel, this ringless metered 50/30/20 Midwest post-mount surface box is made with 16ga steel, finished with a gray polyester powder-coated paint that is baked on and NEMA 3R rated for outdoor use. The rolled-edge receptacle door swings up and open and can be locked. Units come factory wired and are assembled with breakers and receptacles installed
| Midwest® GE Metered Power Outlet, Type RV Ringless, 120/240 VAC, 100 A, 1 ph, 50/30/20 GFCI Receptacle, CB120/CB130/CB250 Circuit Breaker, 6 to 1/0 AWG Wire, Overhead Feed, 10 kA Short Circuit, NEMA 3R Enclosure, Steel, Surface Mounting |
Features:
- All in one construction for factory assured terminations
- Rolled edge door for cord protection
- Heavy 16 ga galvanized zinc coated steel with highest quality electro deposition finish resists corrosion and fading
- Welded flange, NEMA 3R construction for lasting service in outdoor installations
- All components are factory wired and assembled, reducing installation time
- Door holds in open position for user convenience
- All terminals accept copper or aluminum wire for added installation flexibility
- Wide range of receptacle configurations
- Broad range of concentric knockouts to accommodate wiring needs
- All units with 12 to 2 copper/aluminum equipment ground lug
- Rolled edge post bottoms to protect service cable
- Post door removable for installation ease
- Surface heads
- Hub provision
Heavy Duty Welded Galvanized Picnic Table Frame Kit – 2-3/8" OD, 11 Ga Steel, 6ft or 8ft
Heavy Duty Welded Galvanized Picnic Table Frame Kit – 2-3/8" OD, 11 Ga Steel, 6ft or 8ft
Heavy-duty commercial picnic table frame kit — 6ft or 8ft, welded galvanized steel, in stock and ships fast.
Built with 2-3/8" OD, 11 ga galvanized steel tubing — the same heavy spec used by premium competitors, at a fraction of the price. The welded one-piece construction is structurally stronger than bolted alternatives, and the 11 ga wall thickness is heavier than the 13 ga tubing found on most competing frames. Hardware is stainless steel, not galvanized — won't rust out over years of outdoor exposure.
Frame Features:
- 2-3/8" OD tubing, 11 ga wall — heavier than industry-standard 13 ga
- Welded construction — stronger than bolted frame alternatives
- Stainless steel carriage bolt fasteners included — corrosion-proof
- 1-5/16" OD diagonal braces for structural rigidity
- Extra-wide tip-resistant design — won't tip even with unbalanced load
- Hot-dip galvanized finish with clear lacquer coating
- Works with standard 2x10 lumber — purchase locally to save on freight
- One frame kit fits both 6ft and 8ft tables
Perfect for campgrounds, RV parks, parks, schools, and municipalities. Frame only — lumber not included. Buying lumber locally cuts your total cost significantly compared to purchasing a fully assembled table shipped freight.
Frequently asked questions
What is included?
The welded galvanized steel frame and stainless-steel carriage-bolt hardware. Lumber (standard 2x10) is not included — buy it locally to save significantly on freight.
Does one kit fit both 6ft and 8ft tables?
Yes — the same frame kit builds either a 6ft or an 8ft table.
Why welded instead of bolted?
Welded one-piece construction is structurally stronger and will not loosen over time the way bolted frames can.
What lumber do I need?
Standard 2x10 boards, cut to your chosen 6ft or 8ft length.
Prefer a budget option or a finished table? See the our thermoplastic picnic tables.